Developed by BlueWater Ropes and Yates Gear. Dyna-Stat has all the best qualities of a dynamic climbing rope combined with the static qualities of a low elongation technical rescue rope. Dyna-Stat has been developed specifically for use with the new Petzl RIG as a heli-rappel rope descent system. Dyna-Stat has dynamic properties with just enough stretch to not shock load the helicopter or the rappeller during abrupt stops while on rappel. It is also rugged enough to excel as a technical rescue rope used in lowering and raising systems where a low elongation static rope is desired. Dyna-Stat is an ideal mountain rescue multi-function rope.
Try one and experience the advantage of Dyna-Stat technology. Patent Pending.

• Rope diameter 7/16 inch (11.5mm)
• Available in orange w/blue tracer and black w/OD tracer
• Standard lengths: 200 feet
• Custom lengths and colors available on request
• Sewn termination attachments points with stainless steel captive thimble on both rope ends to allow rope ends to be switched for extended life span

Rope type:..................... Assaultline - Dyna-Stat - Enduro Dynamic
Diameter:.........................11.5 mm......... 10.7 mm ..........11.0 mm

MBS (lbs)(Aver-2S.D.).....7193............... 7912.................5427

Elongation @ 300 lbf:...... 3.40.................3.13..................7.70
Elongation @ 600 lbf:.......5.40.................6.25................16.40
Elongation @ 1000 lbf:.....8.40.................8.85................25.00

Rope falls held:..............4 Fail..............4 Fail............... 15 Pass
Impact force 1st. fall:..11.9 kN............11.2 kN...............8.5 kN

NFPA elongation certification:
< 10% at 10% MBS:......... 6.20%.............. 9.40%............. 14.70%

Designed specifically for heli-rappel and short haul operations with a single frontal attachment point located two inches below a standard sternal attachment point, 4 inches above normal waist attachment. This new sub-sternal steel D ring attachment is the perfect balance point to allow a secure and comfortable attachment location while limiting unintentional inversion. Harness cannot be taken apart or chest separated from seat portion. Waist belt portion of the harness uses smaller and thinner padding material to save weight and reduce bulk. Wide anatomical leg pads offer adequate comfort and support. Leg pad orientation can be adjusted to accommodate personal preferences. Easily donned and adjustable for variations in clothing and user size by use of forged two piece friction buckle system. Steel dorsal D ring is easily adjustable on rear of chest. 3600 lbf. personal retention lanyard D ring attachment located in center rear of waist pad. Shoulder straps are specially tailored to reduce chafing of the neck. Weight 3 lb. 15 oz.

• Sizes S/M, L/ XL
• UL classified to meet NFPA 1983/2012 edition standards
• Meets ANSI/OSHA Class III harness standards
• Optional contoured shoulder pads available (item 414)

Product Information and training video (Yates Gear on VIMEO)

Designed specifically for heli-rappel and short haul and hoist operations with a single frontal attachment point. Color coded
webbing allows for easy and fast donning of harness. Reflective tape is added to front and back of harness. This new substernal steel D ring attachment is the perfect balance point to allow a secure and
comfortable attachment location while limiting unintentional inversion. Harness cannot be taken apart or chest separated from seat portion. Same waist and leg padding system as standard 388 Heli-Ops Harness. Easily donned and adjustable for variations in clothing and user size by use of forged two piece color coded friction buckle system. Steel dorsal D ring is easily adjustable on rear of chest. 3600 lbf. personal retention lanyard D ring attachment located in center rear of waist pad. Shoulder straps are specially tailored to reduce chafing of the neck. Weight 3 lb. 15 oz.

• Sizes S/M, L/ XL
• UL classified to meet NFPA 1983/2012 edition standards
• Certification for FAA TSO-C167 in process
• Meets ANSI/OSHA Class III harness standards
• Radio mic tabs on shoulders
• Optional contoured shoulder pads available (item 414)

Designed for rope access work (expert users only). Multi-function handle allows the user to unlock the rope and control the descent with the hand on the free end of the rope and position themself while on the rope without tying off the device. The automatic return system on the handle limits risks in case of an involuntary action by the user. The safety gate on the moving side plate helps prevent dropping the device and facilitates installation of the rope and passing intermediate anchors. Can also be used for short ascents (RAD system). For rope between 10.5 and 11.5mm in diameter. Colors: Black ($155.00) or Gold.

Product Information and training video (Yates Gear on VIMEO)
Petzl product information and training video

Designed for use as a full body harness for insertion and extraction (SPIE) applications. Works well for emergency egress from multistory buildings or rooftops. Dorsal D ring is used for SPIE Lanyard attacnment (Item # 364). Safety sternum strap with Cobra quick connect buckle for added security during SPIE usage. Sternum level attachment point allows an injured or wounded soldier to be lowered in an upright position (Used with Extraction/Personal Retention Lanyard item # 566).Cobra quick connect buckles on leg portion of harness for easy and fast donning. Designed to be worn over tactical web gear and body armor. Weight 1 lb. 12 oz.

• One size fits all
• Available in terra, black and foliage green

• SPIE Lanyard (item 364) not included
• Extraction/Personal Retention Lanyard (item 566)
not included

COBRA ANSI Certified leg buckles

22 inch lanyard made of 7000 lbf. (31kN) nylon webbing. Designed to girth hitch to dorsal D ring of Yates Stabo or Extraction harness for SPIE extraction operations. Green gate DMM Tactical OvaLock 3 Stage aluminum carabiner w/captive pin included. Made in USA.

For use as a personal retention lanyard in a helicopter. Designed using the first all black, non reflective, oxide plated quick release shackle made of stainless steel by Ronstan. Oversize quick release shackle allows the user to easily release from harness or belt in the event of an unplanned landing. Swedged release pin (SOCOM requirement) eliminates plunger pin from releasing in the event the retaining ring is broken. Retaining split ring is safety TIG welded. Quick release shackle uses velco to secure the release tab in place to lessen the chance of inadvertent release. Built with mil spec 5625 tubular webbing, this lanyard tests at over 3400 lbf. (15kN) breaking strength. Kong Tango double locking snap hook is classified to meet NFPA 1983/2006 edition standards. Strength 7425 lbf. (33kN). Made in USA.

• Available in terra and black
• Length retracted 20 inches
• Length fully extended 31 inches

NEW Mini Bird Helo Personal Retention Lanyard
• Lanyard without retraction bungee inserted in webbing
• Length 16 inches

For use as a personal retention lanyard in a helicopter. Designed using the first all black, non reflective, oxide plated quick release shackle made of stainless steel by Ronstan. Oversize quick release shackle allows the user to easily release from harness or belt in the event of an unplanned landing. Swedged release pin (SOCOM requirement) eliminates plunger pin from releasing in the event the retaining ring is broken. Retaining split ring is safety TIG welded. Quick release shackle uses velco to secure the release tab in place to lessen the chance of inadvertent release. Built with mil spec 5625 tubular webbing, this lanyard tests at over 3400 lbf. (15kN) breaking strength. Kong Tango double locking snap hook is classified to meet NFPA 1983/2006 edition standards. Strength 7425 lbf. (33kN). Made in USA.

Yates SCREAMER Shock absorber added for energy absorbtion. In the event an activation force of 2.5 kN (600 lbs) is exerted on the lanyard during a fall the SCREAMER has the potential to absorb 2-3 kN of energy if fully activated (11 inches).

• Available in terra and black
• Length retracted 26 inches
• Length fully extended 42 inches

For use as a adjustable length personal retention lanyard for Rappel Masters, Crew Chiefs and Riggers. Designed to connect to users harness and to fixed surface or helo rappel point via unique aluminum snap hook. Lanyard has adjustable length using Yates adjustable dasy chain system. Adjuster buckle has strength of 6 kN. Kong Tango has 1.1 inch gate opening. Built with mil spec. 5625 tubular webbing, the ultimate strength of lanyard tests over 3400 lbf. (15kN) breaking strength. Kong Tango double locking snap hooks are classified to meet NFPA 1983/2006 edition standards. Strength 7425 lbf. (33kN). Made in USA.

Yates SCREAMER Shock absorber added for energy absorbtion. In the event an activation force of 2.5 kN (600 lbs) is exerted on the lanyard during a fall the SCREAMER has the potential to absorb 2-3 kN of energy if fully activated (11 inches).

• Available in terra and black
• Length retracted 18 inches
• Length fully extended 47 inches

Sold as complete set of retention lanyards for the operators while working Helo operations with ship door in open position who backup security of a redundent lanyard system. Only one lanyard has quick release option. Set combines one Rappel Master Lanyard(571) and one Helo Personal Retention Lanyard w/Shock Stop(569).

• Lanyard 571(Blue), Lanyard 569 (Orange)

For use as a personal retention and extraction lanyard. Designed to attach to users harness and connect to extraction point or Helo hard point via unique New DMM captive Eye Carabiner. Built with mil spec 4000 lbf (18 kN) 5625 tubular webbing. Lanyard rated strength 3400 lbf. (15kN). High strength hot forged aluminum alloy captive eye carabiner. Unique patented "Locksafe" three stage autolocking gate mechanism allows for 3600 lbf. (16kN) gate strength. 100% Proof loaded to 3,600 lbf (16kN). Minimum strength 6750 lbf. (30kN).Carabiner manufactured in Wales by DMM Ltd. Carabiner NSN: 8465-99-151-3939

Certified to: ANSI/ASSE Z359.12(09)-1992. EN362-2004 and CSA Z259.12-11. Lanyard Made in USA.

• Available in terra and black
• Length retracted 23 inches
• Length fully extended 36 inches

For use as a adjustable length personal retention lanyard for Rappel Masters, Crew Chiefs and Riggers. Designed to connect to users harness and to fixed surface or helo rappel point via unique New DMM captive Eye Carabiner. Built with mil spec 4000 lbf (18 kN) 5625 tubular webbing. Lanyard rated strength 3400 lbf. (15kN). Lanyard has adjustable length using Yates adjustable dasy chain system. Adjuster buckle has strength of 6 kN.High strength hot forged aluminum alloy captive eye carabiner. Unique patented "Locksafe" three stage autolocking gate mechanism allows for 3600 lbf. (16kN) gate strength. 100% Proof loaded to 3,600 lbf (16kN). Minimum strength 6750 lbf. (30kN).Carabiner manufactured in Wales by DMM Ltd. Carabiner NSN: 8465-99-151-3939

Certified to: ANSI/ASSE Z359.12(09)-1992. EN362-2004 and CSA Z259.12-11. Lanyard Made in USA.

Yates SCREAMER Shock absorber added for energy absorbtion. In the event an activation force of 2.5 kN (600 lbs) is exerted on the lanyard during a fall the SCREAMER has the potential to absorb 2-3 kN of energy if fully activated (11 inches).

• Available in terra and black
• Length retracted 18 inches
• Length fully extended 47 inches

Thick full-grain "Nrw" double layer palm extends over the palm and to the second joint of your fingers to provide added protection from the heat and friction generated when fast roping. Index finger is separated for trigger finger dexterity. Designed to fit over flight gloves. Also excellent for tactical and helirappel use. Carabiner hole in wrist for attaching to harness.

• Available in black and milti-cam
• Sizes: S-2XL